Foxthereal

Fix BOOTMGR missing with a Windows DVD If you have a Windows installation disk, you can directly use it to fix the Bootmgr missing issue. If you don't have one, the first way is recommended, because it can save you much on purchasing a Windows installation DVD. Next, let's check how to fix Bootmgr missing problem with a Windows DVD in steps. The boot error “BOOTMGR is Missing” in Windows The BOOTMGR error can be caused by many things, including boot sector viruses, failed Windows installs or updates or crashed hard disks. A very common reason for your PC to fail loading and displaying this error is when it tries to boot from a hard or flash drive that is non-bootable.

Summary :

Have you encountered the situation when a black screen pops up and says 'BOOTMGR is Missing. Press Ctrl+Alt+Del to restart' while you are booting your Windows 10/8/7/XP computer? Don’t worry and take it easy! This post will walk you through 11 useful solutions to fix the issue of Boot Manager missing.

What Is BOOTMGR

BOOTMGR is short for Windows Boot Manager which refers to a small piece of software that is loaded from the volume boot code. Usually, the BOOTMGR file is read-only and is locating in the boot directory of the partition which is set as 'active'.

On most PCs, the partition is labeled as system reserved without a drive letter. If there is no system reserved partition, BOOTMGR probably locates in your primary partition C. BOOTMGR can read boot configuration data and display the operating system selection menu.

However, sometimes BOOTMGR may be missing or lost due to reasons including incorrect bootable disk, damaged MBR, outdated BIOS, loose or damaged hard disk interface cables, etc.

BOOTMGR Error Messages

This issue usually appears shortly after the computer is turned on, immediately after the Power On Self Test (POST for short) is complete.

When the BOOTMGR error message occurs, the Windows has initially started to load. And you can see the message 'BOOTMGR is missing. Press Ctrl+Alt+Del to restart', as shown below:

In addition, you may receive different messages like 'BOOTMGR is missing. Press any key to restart' or 'CDBOOT: Couldn't find BOOTMGR'.

11 Solutions to Missing BOOTMGR

1. Restart your PC
2. Remove all removable media
3. Change boot order in BIOS
4. Repair Master Boot Record
5. Mark partition active
6. Test hard drive
7. Run Windows Startup Repair
8. Reseat all internal data nad power cables
9. Update BIOS
10. Clean Install
11. Replace the hard drive

How to Fix BOOTMGR Is Missing Windows 7/8/10

When the issue “Windows couldn’t find BOOTMGR or missing BOOTMGR” occurs, you would try to search for solutions on the internet. Here we have summarized eleven solutions for you and hopefully, you can solve your problem on your Windows 7/8/10 computer.

Here is a related video for you:

Solution 1: Restart Your Desktop or Laptop

Once Windows prompts you “BOOTMGR is missing, please try to restart your PC by pressing Ctrl+Alt+Del keys or any key”, follow what the error message suggests first because maybe the BOOTMGR error is just a fluke.

However, sometimes a reboot can’t solve the BOOTMGR problem. Therefore, please try the following ways if rebooting did not work.

Solution 2: Remove All Removable Media

Since BOOTMGR error can be caused by booting your computer from a non-bootable hard drive, you should check if your PC is configured to boot from a USB flash drive, a floppy disk, or other non-bootable disks.

If this is the problem, please remove the device and make sure your BIOS doesn’t load from any of them. Otherwise, missing BOOTMGR issue will happen again.

Solution 3: Change Boot Order in BIOS

After unplugging a non-bootable disk, perhaps Boot Manager not found error will still appear. In this case, you need to consider checking the boot sequence in BIOS.

Step 1: Restart your computer.

Step 2: Then press a specific key to go to the main interface of BIOS.

Step 3: Then under the Boot tab, modify the boot order to set the hard drive as the first boot device.

After restarting PC, if the error “Boot Manager is missing” still happens, try to look for the next way.

Solution 4: Repair Master Boot Record

It is most likely that the message “BOOTMGR is missing” happens due to damaged Master Boot Record (MBR). In this case, it is necessary to repair MBR. You might be wondering about how you can repair MBR to fix BOOTMGR is missing with USB drive effectively; especially when the operating system is unbootable.

Don’t worry, we will introduce you a piece of professional partition and disk management software – MiniTool Partition Wizard. This tool has multiple editions including Free, Pro, Pro Ultimate, Server and more which are designed for users with different needs.

Professional Edition and the advanced editions all have a feature called Bootable Media, which is available when there is no OS or OS fails to boot.

If you fail to boot your Windows 7/8/10 OS due to the error “BOOTMGR is missing”, you can try this function. Unfortunately, the Free Edition doesn’t support this feature.

Step 1: A few seconds later, you will see the MiniTool PE Loader interface. Please launch MiniTool Partition Wizard.

Step 2: In the MiniTool Partition Wizard main interface, right-click the target disk and choose the Rebuild MBR feature.

Step 3: Click Apply to perform MBR restoration. After finishing this operation, please exit the program and restart your computer again. The “BOOTMGR is missing press Ctrl+Alt+Del to restart” error might be solved by this way.

In addition to performing MBR recovery, some of you choose to use the bootrec tool. Firstly, you need to prepare a Windows installation disc and connect it to your PC. Next, try to repair the issue “BOOTMGR is missing” in Windows 7 with Command Prompt.

Please launch CMD according to the wizard. On Windows 7/8/10, type the following commands in turn:

bootrec /fixmbr

bootrec /fixboot

bootrec /rebuildbcd

Tip: For Windows 8/10, you need to type bootrec /scanos before rebuilding BCD.

To fix BOOTMGR using CMD seems to be a bit complicated. Therefore, here we suggest using MiniTool Partition Wizard since it is a more convenient solution.

Solution 5: Mark Partition Active

If you have marked a wrong partition active, the computer will fail to start up and show the BOOTMGR error message because the active partition probably doesn’t contain boot files. In PC there is only one active partition and system partition or boot partition must be primary and active.

In this case, you must mark the partition within boot files active to ensure the computer runs properly. In order to solve the issue, please reset your system partition active.

How to mark the partition active to fix “BOOTMGR is missing” on Windows 7/8/10? You can use MiniTool Partition Wizard Professional Edition as well and the operation is also very simple. Remember to boot your computer from the bootable disc or USB drive to enter the main interface of MiniTool Partition Wizard first.

Step 1: Select the wrong active partition. You could see there are many partition functions in the left pane and please select Set Inactive.

Step 2: Select the target partition, click the Set Active function from Partition Management menu.

Step 3: At last, you will go back to the main interface of MiniTool Partition Wizard again and click the Apply button to make these changes effective.

Solution 6: Test Hard Drive

Another reason that may cause BOOTMGR files missing is that there are some bad sectors. What you need to do is to check the disk surface.

MiniTool Partition Wizard provides a feature to do this with its Surface Test on Windows 7/8/10. If bad sectors exist, this tool will mark them red. On the contrary, healthy sectors will be marked green.

Related article:What to Do If I Find Bad Sectors on Hard Drive in Windows 10/8/7?

Once bad blocks are found, you can use the chkdsk tool to shield them. If there are many bad blocks, in order to avoid data loss, please back up the significant data on the target disk.

Fortunately, MiniTool Partition Wizard has those two functions: copy partition and copy disk. Here we strongly suggest cloning the entire disk data to an appropriate hard drive.

Are you experiencing the same issue? Now try MiniTool Partition Wizard Professional Edition to create a bootable disc or USB drive to boot your computer and then fix the issue of missing BOOTMGR on Windows 7/8/10.

If there are no logical bad sectors detected on your hard drive, you can skip the backup operation and try the next solution.

Solution 7: Perform Windows Startup Repair

In addition, you can perform a Windows startup repair. This way can replace any missing or corrupted files, including BOOTMGR. You may be wondering that if there is no CD disc, can BOOTMGR is missing Windows 7 fix without CD be done? In other words, how to fix BOOTMGR is missing in Windows 7 without CD?

Create a bootable USB from ISO and then boot the PC from the USB drive to enter the Windows Recovery Environment. On Windows 7, choose Startup Repair under the System Recovery Options window to continue.

On Windows 8/10, go Troubleshoot → Advanced options → Automatic Repair(Windows 8) or Startup Repair(Windows 10).

Solution 8: Reseat All Internal Data and Power Cables

The above content mentioned the “BOOTMGR is missing press Ctrl+Alt+Delete to restart” error could be caused by loose, unplugged or malfunctioning power cables. Please try to replace the old cable with a new IDE one to check whether your cable works or not.

Solution 9: Update the Motherboard BIOS

If the BIOS on your motherboard is outdated, sometimes you will get a BOOTMGR error message. Thus, you should ensure the BIOS is upgraded to the latest version. If it is not, try to update it first since the BIOS must be available on your computer. If you don’t know how to update it, you could find the way from the article How to Update Your BIOS.

Solution 10: Perform a Clean Windows Installation

If all the solutions above did not work when trying to solve the Boot Manager missing issue, it is a good way to perform a Windows installation to repair this error. This way, it will completely remove Windows from your PC. However, all data will be deleted so you’d better back up important files before re-installing OS.

At first, follow solution 6 which shows you how to clone disk or partition using MiniTool Partition Wizard. Then you can start to install a new operating system. There is another professional backup software: MiniTool ShadowMaker that you can use it for Windows 10/8/7. It’s very easy to back up data without booting OS with the help of this software.

Solution 11: Replace the Hard Drive

If you still receive a BOOTMGR message, you should consider that the hard drive has a physical issue. The only solution for this situation is to replace the died or damaged hard disk with a new one and re-install Windows after that.

Bottom Line

Here you have come to the end of this post. After learning so much information about BOOTMGR, we think you now know what “BOOTMGR is missing” error is and understand several solutions to solve the BOOTMGR error. Now, it is time for you to solve this problem in order to fix your computer and make it runs normally.

If you have any suggestions to fix BOOTMGR on Windows 7/8/10, please don't hesitate to tell us by leaving a comment below or sending an email to [email protected]. Thank you!

BOOTMGR Is Missing FAQ

Bootmgr, commonly known as boot manager, is the code that provides your computer with instructions on how to boot into the operating system. If bootmgr is missing from your hard drive, or is.

This guide will show you, how to use WinSetupFromUSB to create a bootable USB Flash Drive including all Windows source files, plus the following installation of Windows XP. Compare to the different USBMultiboot versions, WinSetupFromUSB comes with a Graphical User Interface (GUI) and is in my opinion easier to use. You can get the latest version of the program and you will also find many detailed informations about WinSetupFromUSB. I’ve tested this guide with a 32-bit version of Windows XP and a 64-bit version of Windows Vista and it worked flawlessly.

Prerequisites: All you need is:. a USB Flash Drive with at least 1GB of storage. the original Windows XP Setup CD. WinSetupFromUSB If you use nLite to slim down your version of Windows XP, please keep the following in mind. DO NOT remove “Manual Install and Upgrade” under Operating System Options! I also recommend to Service Pack 3 into your Windows XP source files. Preparations Download and install WinSetupFromUSB.

Default installation path is C: WinSetupFromUSB. Create a new folder with the name WINXPCD in the root directory of drive C: and copy all files from your Windows XP Setup CD into this folder. Depending on your version of Windows XP, the content of C: WINXPCD should look approximately like this: The following files will show you, which Service Pack is already integrated into your CD:. WIN51IC.SP1, Sevice Pack 1. WIN51IC.SP2, Sevice Pack 2. WIN51IC.SP3, Sevice Pack 3 2.

Start WinSetupFromUSB Connect the USB Flash Drive to your PC and start WinSetupFromUSB. It should show up under USB Disk Selection: 3. Select your Source Path Click on Browse under Windows 2000/XP/2003 Source and navigate to the folder with your Windows XP Source Files.

It should be C: WINXPCD: Click OK and C: WINXPCD should show up under Windows 2000/XP/2003 Source: 4. Format USB Flash Drive PeToUSB or HP Format Tool are used to format the USB Flash Drive. There is no need to download these programs seperately as they are already included in WinSetupFromUSB. USB Flash Drives up to 2GB should be formatted with PeToUSB in FAT16, USB Flash Drives with 4GB or more with HP Format Tool in FAT32.

I will use PeToUSB to format my Kingston Data Traveler with 2GB. In the main window of WinSetupFromUSB click PeToUSB under Format target using to start the program. The USB Flash Drive should show up under Destination Drive.

Check USB Removable, Enable Disk Format and Quick Format. Uncheck Enable File Copy under File Copy Options: Click Start and answer the following two questions “Continue?” with Yes. All existing volumes and data will be lost!

If everything goes well, the message “Operation Completed Successfully!” should appear. Click OK and close PeToUSB. The process with HP Format Tool is similar. Copy Windows XP Source Files To start the process of copying the Windows XP source files to the USB Flash Drive, click GO in the main window of WinSetupFromUSB. Depending on the write speed of your USB Flash drive it may take a while to copy all files. At the end the following notice about the Windows installation process should be displayed: Click OK and close WinSetupFromUSB with EXIT. Windows Installation – Part 1 Connect the USB Flash Drive to your PC and turn on the computer.

Press ESC at the boot screen and you will be able to select the USB Flash Drive as your boot device from the boot menu. The ESC key is used by ASUS for the Eee PC series. Other manufacturers may use other keys, e.g.

After booting from USB Flash Drive, the following menu should be displayed:. Windows XP/2000/2003 Setup – First and Second parts Press Enter or wait 10 seconds to get to the next menu:. First part of Windows XP Home Edition setup. Second part of XP Home Edition setup+Start Windows for first time First part of Windows XP Home Edition setup is already selected. Press Enter or wait 10 seconds to start the Text mode part of setup.

During this part you can create, delete and format partitions and finally the setup files are copied to your hard disk. At the end the system will restart automatically. Windows Installation – Part 2 After restart, boot the PC again from your USB Flash Drive.

The same menu should be displayed:. Windows XP/2000/2003 Setup – First and Second parts Press Enter or wait 10 seconds to get to the next menu:. First part of Windows XP Home Edition setup. Second part of XP Home Edition setup+Start Windows for first time Second part of XP Home Edition setup+Start Windows for first time is already selected. Press Enter or wait 10 seconds to start the GUI mode part of setup. During this part you will be asked for your product key, timezone, usernames and other necessary informations. At the end the system will restart automatically.

Windows Installation – Part 3 After restart, boot the PC again from your USB Flash Drive. The same menu should be displayed:. Windows XP/2000/2003 Setup – First and Second parts Press Enter or wait 10 seconds to get to the next menu:. First part of Windows XP Home Edition setup.

Second part of XP Home Edition setup+Start Windows for first time Second part of XP Home Edition setup+Start Windows for first time is already selected. Press Enter or wait 10 seconds to Start Windows for the first time.

The Windows installation process will be finished and finally the Windows Desktop will appear. @ limubear Yes, exacly the same procedure as doing a clean install of Windows. You just install it from USB instead of a CD or DVD drive. The drivers you can find on the support DVD.

Some have been updated recently so you better download them from the ASUS Support site. I install them in the following order: 1. Touchpad Some people prefer to install the ACPI driver after Chipset, Audio and VGA. After installing all drivers and ASUS Software run Windows Update.

Then continue with the rest of your software. Hi man thanx for this Note, iam very happy to see this Subject We have an arabic site translate your Subject to our language and alot of people Benefit from your Subject. ” ” We wana to know from you why when i press F12 its give me only Boot from lan or hard drive, and didnt give me to boot from Flash when i wana to change my first boot from Cdroom and make it usb, it give 4 usb ” Usb-Hdd / usb-FDD / usb-cdroom. And i try to use all of this and didnt get boot So please I need your help to fixed this Error thx my frind Zizo From Egypt. @Sam AV programs typically are quite sensitive to AutoIt scripts, which was used to make WinSetupFromUSB.

There have been false alarms every now and then with almost any compiled AutoIt script I’ve come across. A quick Google search with keywords like “autoit false positive virus” will give you numerous examples. If you have downloaded the tool from msfn.org, and the downloaded exe was not infected after downloading it, rest assured there are no viruses or malware in the package. If you want to do good- contact the antivirus company you use about the false positive. Do cross-check as well: virusscan. Hi, Can you publish, or point to, detailed guide on how to prepare USB stick, how to install Win XP Pro SP2 or Micro XP v0.82 on the formatted USB stick, and how to boot and run XP Pro or XP Micro directly from the USB stick.

The question is about Portable OS where if the USB stick is plugged before PC power-up, the OS on the stick will boot and run instead of the OS on the HDD. I guess in case of running OS from USB stick (2 or 4GB), will be good idea to move the location of the page file to be on the HDD (if the Portable XP uses page file) – if such moving of location is necessary, then corresponding How-to instructions will be needed too. Regards, Homer. Hello, I am having a eeepc 901 and at the moment I am not able to load Windows.

Each time it loads, it’ll prompt me to select “Start Windows Normally”, “Safe Mode”, etc. Similar to when you press F8 when windows is booting up. I observed that there is a blue screen after I select “Start Windows Normally” but I am not able to capture what the blue screen is showing because it will auto reboot and show me the F8 screen again automatically.

What I have is the Recovery DVD from Asus that comes along with the 901 when purchased. Is there a method to recover the 901 using the Recovery DVD via USB instead of via an external DVD device? Appreciate your quick response.

Hi guys, first of all thank you for the great instructions on this page. I have come further with this guide than any other guide Now I’m almost there, installing XP on my laptop HP NC4200 from a USB stick. One slight problem: After following all the instructions, windows wouldn’t boot from HDD.

Bootmgr Is Missing Xp Usb Installation Program For Mac

I get an error message: “A disk read error occurred. Press Ctrl Alt Del to restart” Funny engough the system starts up when I insert the USB stick and go through “Windows installation – Part 3” again. Once gone through this menu, windows functions as normal.

I can even see the USB as a “removable disk” in windows explorer. I followed the instruction and everything looks OK. I have 2 questions: 1. The original CD had a file Setup.exe that provided a few options. This is not on the USB stick. 2) My netbook came wiht 2 DVDs. The instructions only speak about the “starting” DVD.

I think the 2nd DVD has some application and maybe some drivers. Can I just add the content of the 2nd DVD to a directory on the USB stick? I assume all I need is the 1st DVD to actually install XS and I can run the Setup.exe file from the 2nd DVD (now on the USB stick). Does that sound right.

On a final note, I guess I am a bit surprised that the USB stick does not do (act) exactly like the DVD. Thnanks Jerry. @ Jerry A1: I assume you use a Windows XP Setup-CD to create the USB drive. WinSetupFromUSB copies only files to the USB drive that are necessary. Setup.exe is not needed for installing Windows from USB, thats why it’s missing. A2: I cannot help you with this question because i don’t know the content of the 2 DVDs.

Every manufacturer supplies different CDs/DVDs. If you install Windows XP from USB, all you need are the Original drivers and software from the DVDs.

Just look for folders named “Driver” or “Software”. Hi I have a Toshiba NB100 wich had ubuntu installed on it i have tried booting off usb and all goes well boots up in txt mode but when i try to locate my main HDD 80 gig one its not shown in the windows install menu any ideas whats wrong. I deleted all of the drives content using Killdisk thinking that was the problem and drive still not shown now i cant even log onto ubuntu im thinkin only way to solve this is to buy an external disk drive or can i save my money and install of my flash drive please help!!!!!!!!!!!!!!!1. Hello there, I have a Samsung NC10 coming soon and am looking to do a clean install but have a few questions hoping you can help me with. Which XP CD am I to use to copy over to the USB stick? The recovery CD that comes with the NC10 or a stand alone XP CD?

Install Bootmgr On Usb

Will I receive a License Key with the NC10 or will I have to use some sort of software to extract the license key? I have a Vaio laptop and had to extract the license key when I did a clean install of Vista. Should anything go wrong, will I be able to use the recovery CD to restore the NC10 to its exact default state? Look forward to hearing from you and please do forgive me as I am not very computer savvy. “Cannot see hard drive during setup” Hey The installation gets problematic at the point where I need to select a partition to install windows xp onto.

As it turns out, only the flash drive is loaded as a possible installation point. I should note that my hard drive works properly. It is detected on bios and has a working installation which boots properly when the flash drive is not selected as a priority boot location. However, when I go to the restore command prompt in setup (when booting from flash drive), I’m unable to locate my “C” drive. I’d appreciate any help. To the people with the drive letter problems.

I haven’t tried this but it should work: begin the windows installation again (step 1) and the setup wizard should see the xp installation and prompt you to repair it. Enter the recovery console. Change to d: and edit the boot.ini file change this line: multi(0)disk(0)rdisk(0)partition(1)WINDOWS=”Microsoft Windows XP Home Edition” /noexecute=optin /fastdetect to multi(0)disk(1)rdisk(0)partition(1)WINDOWS=”Microsoft Windows XP Home Edition” /noexecute=optin /fastdetect — disk(0) is changed to disk(1) —. First excuse my english second thanks a lot for the work I’d like to say no problem i made the usb keythen decide to test it on a pcinstall 100% ok my hopes were great 😉 then try it on my laptop(with broken cdrom)it boot on the usb key ok but instead of menu(Windows XP/2000/2003 Setup – First and Second parts) i directly arrive in grubDosand there i am a bit lost.is there a solution? Maybe some commands in a right order?

Find /menu.lst.or installor setup or kernel usually i try to solve it myself but it seems i’m the only one in this situationand command lines without a clue of what i’m supposed to do is a bit tricky so please some advices or a solution would be very nice thank you in advance. I NEED to say this. T-H-A-N-K Y-O-U!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! You just saved my life!!! I was going to get my a$$ kicked so hard if this didn’t work!

If anyone has problems during the first part of the GUI install, like the “hal.dll” error, don’t freak out. Remove the USB, and turn off your PC. Replug the USB, turn the PC on, and it should be done. Worked for me. It works GREAT. You just saved my Asus Eee PC!

Right now I am installing all of my drivers back. Thank you, so much. Hey just wanted to throw my two cents in. First off I wouldn’t exactly trust that 2009 USB edition from that russian server linked to by “k1d” fuck that. Secondly WinSetupFromUSB has changed a bit. You may need to format your USB before it will appear in the list. It now uses RMPrepUSB, which is great.

Format if going to use XP with an NTLDRit will make it faster for file xfer, then refresh your list and your USB will appear. Everything else seems to work the same. My USB didnt appear when I was looking for it because it was previously formated for another USB install. This seems to be the easiest process I have used so far, compared to the others that use win2003 server updates and shtuff. GL HF Thanks for the tutorial!!!

Finally I was able to install WXP via USB drive to IBM T43 with these instructions! I tried first some other instructions, but text based setup was unable to copy WXP files to HDD!?! Only problem which I had was wrong product key. I’m 99% sure that I had correct key (VLK) for installation media, but setup didn’t accept it.

I did some googling, and found article about that correct product key can be also found from installation media from file i386 UNATTEND.TXT. With this key installation worked perfectly! Thanks for this article and hopefully someone with same problems that I had can find solution to this issues from my comment. =) –Lauri Lattoni.

I would like to say many thanks to you for this wonderful guide. It helped me with restoring my netbook’s factory OS without the crapware and I made to get rid off this netbook sold!, as the wifi card was not recognized by my reasonable OSs anyway.

I must say this: I REALLY REALLY, BUT REALLY HATE WINDOWS. Not Microsoft, not Bill Gates, not Steve Ballmer, etc. I just HATE WINDOWS ITSELF. That piece of junk makes me wonder where humanity is going. As I mentioned – I used to the systems, that actually let you do EVERYTHING with your computer.

They have NO LIMIATIONS. In contrast – Windows has PLENTORA and MYRIADS of limitations and it made me sick so bad I think I have a lot of grey hair now. Thanks for this guide anyway.

It helped me make a good choice: I no longer own this “windows-only” netbook and I’m thinking of getting something “standard-compliant” HW in a future, but who knows? It all depends on how long my actual HW will serve me. I have the Dell Mini 10v.

I’m told it will run MacOS. That’s pretty neat and all, but I really have no need for a Mini-Mac. Don’t get me wrong, I like Macintosh!

If I were a rich man, I’d have a “top of the line” Mac Netbook. My oldest son has one, and he also runs Windows 7 (Either in a window or full screen. As a “Task” makes full use of his hardware etc, I was pretty impressed! But, for $2000.00 I BETTER be impressed!

Bootmgr Is Missing Xp Usb Installation Programmer

My Question: In theory, couldn’t.any. OS be run from a flash drive (as long as your machine supports booting from the USB of course). It would be nice to have MacOS, Ubuntu, and some other versions of Windows.

98se, Vista, 7, XP, 3.11, etc. On various flash drives. Thanks, Joe Bucci joebucci(at)netzero.net. About the grub and find /menu.lst issue I got something (is not the solution, maybe if someone else help): 1 – Enter “find”. It will list the partitions. For me: (hd0,0) (hd0,4) (fd0); 2 – Type “root ” plus pendrive partition. For me: “root (fd0)”; 3 – Press ESC; 4 – Select “find /menu.lst” and type “b”; 5 – If everything worked fine, menu is show.

Press “e” again and replace de root (hd0,0) by the partition choose in step 2 (problably you will need to press “e” again); 6 – Repeat the same above with 1st and 2nd installation parts (including the chainloader); Well, from this point, chosing 1st installation the notebook reboots after trying the “verifying system config” (sorry baout this, mine Windows is PT-BR and this is a free translation) and quick “fail finding NTLDETECT” (or something like that). Problably the notebook didn’t see pendrive as diskdrive and as it was expected to be the harddrive (hd0,0) it crashs. @ruchi Yes, fd means floppy disk and, as I’ve guessed in my first, the issue is Windows installation requires the file in the hd0 partition. Again, as mine pendrive works well in others computers, it means this is a issue with this particular notebook. I’ve searched for some solutions (including the use of map command and trying loading a WinXP.iso) but they were useless (the WinXP.iso may work but needs a ramdisk, or something like that, I haven’t checked that way yet). To solve this we have to find a way to force grub to “see” pendrive as hd0 (by the way, in Setup it do appears as HDD-USB).

I haven’t searched the official grub site and thread, I believe it should be our next aim. Best regards. @ruchi To list drives detected by grub, type “find”. The structure shown can be (hd0) or (hd0,0) like, where the first number is the disk number and the second the partition.

So, if you have a disk with 3 partitions it could be shown as (hd0,0) (hd0,1) (hd0,2). If your HD have only one partition, it will shown only (hd0).

In my case it lists: (hd0,0) – Main HD, main partition (hd0,4) – Don’t ask me why the 4, I didn’t get it either. (fd0) – Pendrive To make sure what is yours pendrive, type “find /menu.lst” (or any other file in your pendrive). @Rahul Last week a customer also complained about the same experience: when trying to install Office 2007 installation program asked for “ww/enterwww.cab” file and she couldn’t continue I googled for a while trying to find a solution but, after spending some time, I had to quit and turn my attention to other matters I would keep searching for it, copying CD to HD won’t work, making a ISO neither, I even read it could be a Windows Home x Office Professional conflict of some sort (I doubt it). Well, by now, I don’t have a solution for this researching. I have a Mini Dell Inspiron 10. I Used WinSetupFromUSB to reinstall Windows Xp. Dear Sir, I have a pen drive of 32gb.it was running alright.Once I formatted with ACTIVE PARTITION MANAGER software and by mistake entered wrong data in MBR setting and saved.Now when ever I insert same in USB drive the computer stops and goes to Blue screen saying BAD-POOL-HEADER.Now I am unable to re format the pen drive since it stops the computer as soon it is inserted.Please help me so that I get back my pen drive in order and able to format it.I have no problem loosing documents and songs in it to recover it.awaiting your positive reply.My computer is window XP with SP3 lenovo.

@Santanu When I said to format it under DOS, I mean to do it outside Windows OS, usually using the Windows Installation Disk. To do it, you have to insert CD on the computer where your damaged pendrive is inserted, boot it (make sure the computer is setup to start from the CD-Rom drive first – it can be configured through the Setup, usually hitting “Del” key when you start computer and then looking for a option like “Boot Sequence” or “1st Boot Device” or something like that). If everything is ok, soon after booting up the computer a “Booting up from CD.

Press a key to continue” (or something like that) will show. Hit any key to start the Windows Installation. Follow steps until a list of devices is show.

If this method works, your pendrive will appear in this list and you will be able to exclude any partition on it and partition it again. Hope this works.

Dear Sir, replying your message please note 1.If I connect this pen drive before turn on computer boots fully that is all desktop icons appears and at the next moment it hangs and stops on blue screen 2.Yes I tried on Safe mode but it stops before desktop icons appears. I have a OS XP CD but I really do not know whether with the same Cd this computer OS was installed.I am little worried since presently I am using my work place computer hence hesitating to do experiment!Tell me how safe to do it? Awaiting your reply. @Santanu I wouldn’t try this at work computers. It’s not that dangerous, but s.t happens, you know. Your CD will do, as far as I know any Windows XP CD does the job. It should be better if it were a step-by-step using photos try this site: In your case, you should stop right on the second picture (of course, as you.DOES NOT.

want do repair your Windows, you will press ESC key). From the second picture on, you should try to identify your pendrive in the list, maybe a “unrecognized partition / format” or SPECIALLY by the size of your pendrive. At this point I can’t help too much ‘cuz it’s a matter of looking what will be show on screen. Maybe your pendrive won’t show at all. But worth a try.

If you find it on the list, just try to delete partition and create a new one. The Windows Installation won’t format your pendrive without installing the OS on it, so, after creating partition you should quit. From this point on, your pendrive would be “healed” and could formated normally through Windows Explorer menu. @Sunil Patel Yes, this issue had appeared before (just use the “Find” command of your browser and enter “2007”). We don’t have a solution for now. But, this may help you: A costumer installed sucesfully Office 2007, she just used another Installation Disk (mine didn’t work). I don’t have many info about how exactly she did it, since she had called another technician (maybe another version Business / Home / Basic or something like that.

But they are all guesses). @HelpMePlease Have you already tried to prepare the pendrive using another Windows Installation Disk (of a friend, maybe)? Hi, I am facing problem while installing windows XP SP3 on my Dell Studio laptop using HP8GB USB drive.

Followed all steps as given. During the step1(text mode), blue screen not showing my internal Hard Disk partitions to select the right partition. Instead, it is showing 8gb USB drive as the only partition to select. I checked the BIOS, it is showing internal hard disk as 500GB size. I removed hard disk from laptop and connected it as external drive in another laptop and verified partitions.

Proper partition is available(500GB FAT32, Primary, Active). Need your help on resolving this issue. Please advice. Thanks Vijay. imgFunkytown (2011)720p Bluray MKV English 2h 12 min 1280×544 x264 – 5880 kbps DTS – 1510 kbps 5.46 GB Genres: Drama Storyline: Lay down in Montreal during the disco curiosity some 35 years ago, Funkytown follows the person of a faction of colorful characters. We issue their lives and tribulations as everybody converges on a regular heart at Montreal’s passionate disco stain: Starlight.

Along the way, some events occupied in point that transformation these characters’ lives. As these characters’ lives expand, the Parti Quebecois takes power changing the cultural scene in Quebec while the disco craze slowly fades. While we charge of up with these many characters – it is Bastien who is a central role of this story. His benumb addiction, dreams to become an actor and womanizing – offset him the “bigger than sentience” commonplace 70s character around which the entirety story revolves. Software – Download Everything! – DuskDown.com.

My pendrive is 1gb and i have ultra iso and i also write my pendrive but wen i start boot from usb pendrive i get this message pres any key to boot usb after that i get this error (inf file txtsetup.sif is corrupt or missing status 18 press any key to exit i want to know when i format the pendrive under which option fat, fat32, fat16 and ntfs and which is the best write method for usb pendrive = usb-hdd, usb-hdd+, usb-zip and usb-zip+ plz tell me the best solution for this error wating for ur reply sir. I was reading your write up on installing Windows XP from a flash drive. I have a few questions though. I am a novice at this but I am willing to give anything a try. When you say create the folder WINXPCD in the root drive of C: I will just right click on my local hard drive C and great a new folder and name it as you instruct correct? I have a WINDOWS XP/SP2 setup CD but I have the SP3 file on a seperat CD.

How do I copy the XP/sp2 setup CD to the source folder and integrate the sp3 files into the source folder? I do have several other questions and I do hope you have the time to contact me so I can have all my ducks in a row so to speak.

Thanks in advance, Gary. This does work. I’ve just used it to re-install XPSP1a on an old Dell Dimension 4600 using the files from the Dell XP Installation Disk. (The disk was slightly corrupt so I couldn’t use it directly for the install, I had to read and copy it over first using a repair program.) I used an SD card attached to a USB card reader.

But when installing on a Dell Dimension 4600 (and probably other Dell machines), note the following: 1. When formatting, make sure you format to FAT16 LBA; PEtoUSB provides this option. In WinSetupFromUSB, make sure DskNr is 0 and Partition is 2, if you’ve got a small Dell service partition at the front of the disk. After WinSetupFromUSB is complete, replace the NTDETECT on the USB device with the correct Dell one you can find on the Web if you don’t have it already; the correct one is 47,596 bytes.

Make sure you have the latest BIOS from Dell which permits installation from USB; the original BIOS does not. Then change the BIOS settings to boot from USB device. (I tried WinToFlash first and had great problems with it.). On my previous post I’ve write: “A forcefull way could be backuping winsetup.lst and overwriting the Second part block with the First part block, so it would enter the text setup.”. Had you tried this?

Winsetup.lst would look as follow: color black/cyan yellow/cyan timeout 10 default /windefault title First part of Windows XP Professional setup root (hd0,0) chainloader (hd0,0)/$WINNT$.BT/SETUPLDR.BIN savedefault 1 title First part of Windows XP Professional setup root (hd0,0) chainloader (hd0,0)/$WINNT$.BT/SETUPLDR.BIN savedefault. I would advice you to try doing tutorial again from beginning, but I believe you already done so several times. Take a look at “Boot.001″ file. No problem, mate. Even here at office some notebooks could be repaired this way, others just don’t, for the most diferent reasons and error messages. Here I entered setup’s first part, even chosing to enter second part. It may work for you too.

Better backup your pendrive files first, it will be a mess: 1 – Make a backup of the folowing files, located at pendrive’s root: BOOTFONT.BIN NTDETECT.COM NTLDR TXTSETUP.SIF 2 – Enter $WINNT$.LS I386 and copy everything to pendrive’s root; 3 – Rename NTLDR to anything else (NTLDR2, for instance); 4 – Rename SETUPLDR.BIN to NTLDR (no extension, of course); And give it a go. Here it enters first part setup. I don’t know if it will go all the way, though, since I don’t have any available machine to do a fresh Windows install at the moment. Aw, very disapointed reading this, I was hoping this would solve your problem for good. Well, opening TXTSETUP.SIF there is the following text, few past file’s beginning: SourceDisksNames.x86 1 =%cdname%,%cdtagfilei%, i386 This problably was caused because we copied everything from i386 folder to pendrive’s root before. So, I would suggest you to replace every i386 from that file for “” (as you can see on some lines on same file, including the double quotes-space-doublequotes) as stated on this line: 1 =%bootname1%,”%boottagfile1%”,”” If you’re using notepad, just go to edit menu replace (or Ctrl + H shortcut) and enter i386 as searched and “” as replaced (note: double quotes must be exactly the same of those on file – don’t tape them, copy and paste to avoid fails).

Save file and try again. It may solve that problem and may solve your problem, but I believe more erros could occur have you ever considered using Acronis True Image? You could make a backup of a working system, and using it to do a universal restore.

It may work too. Try to make a Backup of your data (using a Linux external harddrive or even a Windows external harddrive – see usbboot.org for details) before trying to do the following: Follow instructions here and prepare a Windows XP USB stick. Start setup and procede normally until asked to choose a partition to install. Choose the one where your C: Windows is.

If all happens right, it will detect and existing Windows instalation and will ask you to chose between Repair or Overwrite. Choose Repair. If problem persists, specify what error is show on screen. “Setup cannot copy the file: default.pif” i have used 3 different XP CDs and still get the same error.

I need to do a clean install because i have Tenga.gen in my system. Have been working on this for past 3 consecutive days.

Also have issue with hal.dll thus i can’t boot into Safe Mode to remove the virus. Have also tried copying/replacing “hal.dll” from my bootable USB to my C: drive and also failed. Says something like cannot be copied but when i explored my XP CD on my stable system(spare PC), its in there. Is there any anti-virus that runs in grub or any that doesn’t require me booting into Windows that you could recommend? I am using Lenovo S10, OneKeyRecovery doesn’t work. I have EISA partition but how do i access it so that i could Reset to Factory Settings? Have you tried those other options on 2nd part or they don’t even show?

Bootmgr Is Missing Xp Download

Have you tried format pen drive and do all steps again? Have you checked at grub4dos menu if 2nd party entry is correct at code level (there is a key you press when you select any option at grub4dos menu to show this, I just can’t remember what is it – I guess it is the “E” key)? Have you ever thought installing Windows 7 instead? Microsoft offers a free tool to make a bootable instalation pen drive (you still need a Windows 7 iso, though).

Solved: for those who have problems booting from target drive after completing the installation proccess and after removing the usb stick: My laptop couldn’t even find the boot.ini during the boot proccess. So I booted from a partition manager application (Hirens, Parted, whatever) and I realize that the boot parttion was not PRIMARY but EXTENDED and INACTIVE-LOGICAL!

I converted it and then changed the boot.ini line that coresponds to that partition and finally I managed to boot from the newlly installation partition. – Most successful bloggers blend their humor with writing and obtained effective results. If you are getting an internet business off the ground, or you have been in the game for a while, but don’t understand why you can’t get a good response from your clients or prospective clients, than you already know that communication is one of the most important currencies around when it comes to doing businesses online.

This will backup the My – SQL WordPress database, which can be restored using php – My – Admin. I’m really sorry you are facing problems with this software.

For self experience, I can say this doesn’t work with all machines. For me, for instance, let’s say this worked 70% of machines tried. On the other 30% (failures), I had to find a workaround, as making an image file of a working PC and copying that over target machine using Acronis True Image Home or, in last case, installing Windows on an external USB hard drive through usboot.org. As a simple user (as you) and not program’s owner or developer, I can only provide limited support and helping. I don’t know if I can help you any further, my best guess right now would be to advise you to buy an external CD Drive (if your notebook doens’t have one). Have you tried any Linux Live CD, just to make sure there is no hardware failure? On my pendrive I have EasyPeasy and Ubuntu Live CDs Images just to test things like Wifi connection and such.

Hello, I have followed the post and successfully was able to format and install an ISO of Windows XP Home Edition using the WinSetupFromUSB.exe software. The GRUB bootloader works like a charm and I select the first option to install the first Windows XP step. The loader looks like it loads and shoots a few lines of text across the screen (too fast to read) and then goes to a black screen. Nothing happens after that. The HDD icon flickers, but that is it. I have left it for over 2 hours and then force rebooted to find the Ubuntu flavor already installed on the HDD still works (which means the GRUB did nothing).

Can I please have some assistance with figuring out what the issue could be? Attempting on a Gateway Netbook LT3117u – Desinged for Windows XP Home Edition but has Ubuntu 12.04 currently 1GB DDR 2 667mhz RAM Athlon 64 (Mobile) L110 1.2 Ghz single core 160GB HDD THANK YOU!

Have you tried using other USB ports? I have experienced some notebooks which only supports loading through an USB stick on specific USB ports (and some which just don’t work at all – but those usually TELLS you they won’t work, so I believe it is not your case here). Other things you can check: If disk access in Setup is configured to IDE or AHCI. Try booting using the pendrive in another computer / notebook just to make sure installation is passing the first steps (don’t worry, it doesn’t do any changes without asking you first). If you’re trying to emulate a Windows CD Image (or any other image, really), verify if the image is contiguous. Try to time and hit “Pause / Break” on your keyboard to try to “freeze” the screen on the exact moment text pops up. You can alternate “Pause / Break” with “PrintScreen” quickly to pause-unpause as a kind of slowmotion.

Thank you very much for the reply! Here is where I am. I verified the files load properly by plugging the stick into another laptop and loading the GRUB bootloader. I tried changing drive access but it appears this Gateway BIOS does not support such functions. Using the Pause/Breakmethode, once I select the first Windows option from GRUB I get this string of commands: Shifting USB disk to be last Found 2 disks, set USB disk hd1 Filesystem type is ntfs, partition type 0x07 Filesystem type is iso9660, using whole disk Will boot NTLDR from drive=0xff, partition=0xff(hidden sectors=0x0) LaunchingSetup from (hd1,0) Setup is inspecting your computer’s hardware configuration Then the screen will go blank and sit there indefinitely. The only thing I can thing may be affecting this is I am using a 16gb DataTraveler 3.0USB pendrive.

Maybe there are some driver problems since this Gateway predates 3.0 technology. Any more thoughts is highly appreciated! Sorry to read that. It may be an incompatibility, indeed.

Telecharger autocad 2015 gratuit avec crack. Have you tried another USB ports on the same notebook? Do you have a Windows 7 installation disc?

If so, you can try making an ISO image, copying to the pendrive and editing the loader so you could try installing that OS. On my pendrive I have Windows XP, Windows 7, Acronis True Image Home and at least 2 Linux ISOs (it could be a good idea adding a Linux ISO too). Another solution could be using Acronis True Image itself. You can make a backup of any computer running Windows XP and trying imaging your notebook using the Universal Restore feature – it restores the image without the drivers from the other PC. You can download the drivers of your notebook to a folder, point that folder under Acronis True Image options or, using Windows 7, let the OS itself detect and install drivers (it could work using Windows XP but I highly doubt). I’ve burrowed my pendrive to a friend so I don’t have the details right now, but I’ll get it back in the next few days.

Uhhh I highly doubt. I’ve installed Windows XP on both IDE and SATA drives for quite some time, both desktop PCs and notebooks and had never found any issue, nor I had to point to driver locations. Usually when Windows XP don’t recognize the HD, installation proceeds normally until the part which it asks which drive you want to install simply because drivers’ list is empty.

As far as I know, by default, Windows XP can’t be installed on external USB drives, but this can be bypass using external tools as the. Our designer is wanting in order to encourage everyone to move for you to. Online via PHP. We’ve always disliked the thought due to expenditures. However he’s tryiong probably none your a lesser amount of.

I’ve already been using Movable-type on various internet sites for approximately a year in addition to are anxious concerning transferring to a new platform. We’ve observed advantages of blogengine. Is there a means I will move most my personal wordpress threads engrossed? Just about any help can be definitely liked!